收藏本站
CAT28F512
WRITE OPERATIONS
The following operations are initiated by observing the
sequence specified in the Write Command Table.
Read Mode
The device can be put into a standard READ mode by
initiating a write cycle with 00H on the data bus. The
subsequent read cycles will be performed similar to a
standard EPROM or EEPROM Read.
Signature Mode
An alternative method for reading device signature (see
Read Operations Signature Mode), is initiated by writing
the code 90H into the command register while keeping
V PP high. A read cycle from address 0000H with CE and
OE low (and WE high) will output the device signature.
CATALYST Code = 00110001 (31H)
A Read cycle from address 0001H retrieves the binary
code for the device on outputs I/O 0 to I/O 7 .
28F512 Code = 1011 1000 (B8H)
Figure 4. A.C. Timing for Erase Operation
Erase Mode
During the first Write cycle, the command 20H is written
into the command register. In order to commence the
erase operation, the identical command of 20H has to be
written again into the register. This two-step process
ensures against accidental erasure of the memory con-
tents. The final erase cycle will be stopped at the rising
edge of WE, at which time the Erase Verify command
(A0H) is sent to the command register. During this cycle,
the address to be verified is sent to the address bus and
latched when WE goes low. An integrated stop timer
allows for automatic timing control over this operation,
eliminating the need for a maximum erase timing speci-
fication. Refer to AC Characteristics (Program/Erase)
for specific timing parameters.
VCC POWER-UP
& STANDBY
SETUP ERASE
COMMAND
ERASE
COMMAND
ERASING
ERASE VERIFY
COMMAND
ERASE
VERIFICATION
VCC POWER-DOWN/
STANDBY
ADDRESSES
tWC
tWC
tAS
tWC
tAH
tRC
CE (E)
tCS
tCH
tCH
tCS
tCH
tEHQZ
OE (G)
tGHWL
tWPH
tWHWH2
tWHGL
tDF
WE (W)
tDS
tWP
tDH
tDS
tWP
tDH
tWP
tDS
tDH
tOE
tOLZ
tOH
DATA (I/O)
HIGH-Z
DATA IN
= 20H
DATA IN
= 20H
DATA IN
= A0H
tLZ
tCE
VALID
DATA OUT
VCC
5.0V
0V
tVPEL
VPP
VPPH
VPPL
? 2009 SCILLC. All rights reserved.
Characteristics subject to change without notice
9
Doc. No. MD-1084, Rev. K
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
CAT28LV256GI-25T IC EEPROM 256KBIT 250NS 32PLCC
CAT28LV64WI-25T IC EEPROM 64KBIT 250NS 28SOIC
CAT28LV65WI25 IC EEPROM 64KBIT 250NS 28SOIC
CAT310W-T1 IC LED DVR 10CH AUTO 20SOIC
CAT32TDI-T3 IC LED DRVR WHITE BCKLGT TSOT-6
CAT3604VHV4-GT2 IC LED DVR WHT CLR BACKLT 16TQFN
CAT3606HV4-T2 IC LED DRVR WHITE BCKLGT 16-TQFN
CAT3614HV2-T2 IC LED DRVR WHITE BCKLGT 12-TDFN
相关代理商/技术参数
CAT28F512LA-12 功能描述:闪存 64 X 8 512K 120ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512LE12 制造商:ON Semiconductor 功能描述:
CAT28F512LI12 功能描述:闪存 64 X 8 512K 120ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512LI-12 制造商:ON Semiconductor 功能描述:Flash Parallel 5V 512Kbit 64K x 8bit 120ns 32-Pin PDIP Rail 制造商:ON Semiconductor 功能描述:Flash Memory IC
CAT28F512LI-15 制造商:Rochester Electronics LLC 功能描述:
CAT28F512LI90 功能描述:闪存 64 X 8 512K 90ns RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512N-12 功能描述:闪存 64 X 8 512K RoHS:否 制造商:ON Semiconductor 数据总线宽度:1 bit 存储类型:Flash 存储容量:2 MB 结构:256 K x 8 定时类型: 接口类型:SPI 访问时间: 电源电压-最大:3.6 V 电源电压-最小:2.3 V 最大工作电流:15 mA 工作温度:- 40 C to + 85 C 安装风格:SMD/SMT 封装 / 箱体: 封装:Reel
CAT28F512N-12T 制造商:ON Semiconductor 功能描述:Flash Parallel 5V 512Kbit 64K x 8bit 120ns 32-Pin PLCC T/R